Introduction to IPX1 & IPX2 Water Drip Test Apparatus
The IPX1&IPX2 Water Drip Test Apparatus is a product shell protection level testing device designed according to standards such as IEC60529 and ISO 20653, specifically designed to verify the product’s protection performance against vertical dripping and 15 degree inclined dripping. According to the classification of protection levels from low to high, IPX1 and IPX2 testing equipment are entry-level water ingress protection testing equipment, generally suitable for components and finished products with low waterproof requirements.

IPX1 setup schematic diagram

IPX2 setup schematic diagram
During testing, a drip box designed according to standard regulations is placed over the entire sample shell and maintained at a specified distance, with the bottom of the drip box filled with needles at the specified spacing and arrangement. Water flows down from the needle at a specified flow rate to simulate raindrops splashing onto the sample. When conducting IPX1 testing, water droplets fall vertically onto the sample shell, while when conducting IPX2 testing, the sample needs to be tilted to meet the requirement of water droplets falling onto the sample shell at a 15 degree tilt angle. In order to ensure that the entire sample shell is evenly covered by raindrops, the sample needs to be rotated at a specified speed during testing.
IPX1 & IPX2 Water Drip Testers Available from AmadeTech
AmadeTech can provide different styles of IPX1 IPX2 dripping water test equipment based on differences in customer sample size, site conditions, and configuration requirements. The most commonly used is the box type equipment, which has a drip box built into the top ceiling of a enclosed stainless steel test chamber. The sample is positioned under the drip tray to be exposed to rainwater, and the water will not flow to the outside of the machine. There is a water tank at the bottom of the chamber for storing testing water. Throughout the entire testing process, the test water was recycled by a water pump without the need for continuous external water supply. In addition, considering compatibility with larger sample sizes and facilitating clear observation of sample status during testing, AmadeTech can also provide open IPX1 IPX2 water drip test apparatuses, including wall-mounted and frame-supported types. Wall-mounted equipment needs to be fixed on the wall, and the drip box can be lifted up and down. The frame-supported type equipment is equipped with wheels that can move freely, and the drip box can also be raised and lowered under control. Both are compatible with samples of relatively large size and have requirements for the testing site. It must be a dedicated laboratory rain room that allows the testing water to flow to the ground and can continuously supply water to the equipment during the testing process. In addition, AmadeTech can also provide a simplified version of the economical IPX1 IPX2 drip testing equipment – a separate drip box with a flow meter. After obtaining it, users can DIY some basic configurations and fixation, connect the water supply pipe, and conduct IPX1 and IPX2 drip tests.
IPX1 vs IPX2 Testing According to IEC 60529
IP Test Rating | IPX1 Test | IPX2 Test |
Water Flow Rate | 1+0.5 mm/min | 3+0.5 mm/min |
Test Duration | 10 min | 10 min (2.5 min for each position of tilt) |
Simulated Dripping direction | Vertically falling water drops against the sample in normal operating position | Vertically falling water against the sample tilted up to 15° |
Turntable Speed | 1 rotation/min | 2.5 min in each of 4 fixed position of tilt |
Eccentricity | Turntable axis 100mm from the specimen axis | Turntable axis and specimen axis in alignment |
Needle Inner Diameter | 0.4 mm | 0.4 mm |
Needle Grid Spacing | 20 mm | 20 mm |
Raindrop Travel | 200 mm from the needle tip to the upper surface of the sample | 200 mm from the needle tip to the top point of the sample |
Applications of IPX1/IPX2 Drip Test Apparatus
Consumer electronics | Entry level waterproof headphones, Bluetooth speakers, low-level models of smart bracelets/watches, internal structural components of electric toothbrushes, etc. |
Household appliances | Kitchen appliances, bathroom mirror lights, exhaust fans, humidifiers, smart home control panels, indoor appliance casings, etc. are mainly designed to prevent condensation water or slight dripping |
Lighting lamps | Indoor lighting fixtures, light strips, driving power supply, partially concealed outdoor lighting fixtures. If exposed directly outdoors, it usually requires IPX4 or above or IP54/IP65/IP67. |
Auto parts | The interior of the car, sensors, connectors, electrical components inside the car, charging port covers, etc. are used to prevent condensation or slight dripping of water; The requirements for exposed parts outside the car are usually higher |
Security and access control | Indoor cameras, access control panels, alarms, smart doorbells, etc. Outdoor cameras generally require IPX4/IPX5/IPX6 or even IP67 |
Medical equipment | Some medical equipment casings, instrument panels, and indoor equipment are designed to prevent slight dripping or condensation during cleaning |
FAQs
Request a Quote Now
Please feel free to contact us for more details on the product, price, lead time, payment terms, shipment methods, etc. AmadeTech sales engineers will respond within one working day.













